Shablon obertki shokolada alenka. SHablon_SHokolad_ Alenka _Psd_8C0JCN.exe 391.09 KB You may be interested SHablon SHokolad Alenka 8C0JCN SHablon_Obertki_Na_SHokolad_ Alenka _Onlayn_FHJGX2.exe.

I am facing this problem canon ir-2016 display showing download standby not work all keys.erroe red light glowing ani body help me thanks.did u just install a Printer Kit?? The Display will show 'Download Mode' or 'Download Standby' even though the imageRUNNER was not put into download mode. This may also occur after installing the updated Printer Kit-J1 [0446B005AA].

Bekijk en download hier de handleiding van Canon ir2016 Kopieermachine (pagina 79. Bij opstarten vraagt hij download standby wat moet ik doen Gesteld op.

Turning the power on and off will not reset the message. Flashing the machine to the latest system software may resolve the unusual message.

Note: Printer Kit-J1 [0446B005AA] requires the new system software v60.02 be installed on the imageRUNNER. Or re-flash the BOOT ROM with at least version 60.02. Installing System Software on the imageRUNNER 2020 / 2016 Series The following modules must be installed from a PC connected to the copier via a USB cable using the Service Support Tool: - System (main controller) * - Boot (boot program) - PCL (PCL printer kit -J1) * The main controller also controls the reader. To flash the Finisher -U1 (Fin_U1), you must connect the PC to the finisher via a RS232C straight cable and the Downloader PCB (FY9-2034) using the Service Support Tool. Due to copyright restrictions, the 2020/2016 System Software is not available for electronic download.

Please order this 2020/2016 system software as a service part using Part Number FY9-4240-003. To enter Download Mode on the imageRUNNER 2020 / 2016 Series: 1. Hit Additional Functions, 2, 8, and Additional Functions to enter Service Mode.

Press the + or - key to scroll through the Service Mode options. Scroll to '#DOWNLOAD'. Hit the OK key. Did u just install a Printer Kit?? The Display will show 'Download Mode' or 'Download Standby' even though the imageRUNNER was not put into download mode. This may also occur after installing the updated Printer Kit-J1 [0446B005AA].

Turning the power on and off will not reset the message. Flashing the machine to the latest system software may resolve the unusual message.

Note: Printer Kit-J1 [0446B005AA] requires the new system software v60.02 be installed on the imageRUNNER. Or re-flash the BOOT ROM with at least version 60.02. Installing System Software on the imageRUNNER 2020 / 2016 Series The following modules must be installed from a PC connected to the copier via a USB cable using the Service Support Tool: - System (main controller) * - Boot (boot program) - PCL (PCL printer kit -J1) * The main controller also controls the reader. To flash the Finisher -U1 (Fin_U1), you must connect the PC to the finisher via a RS232C straight cable and the Downloader PCB (FY9-2034) using the Service Support Tool. Due to copyright restrictions, the 2020/2016 System Software is not available for electronic download. Please order this 2020/2016 system software as a service part using Part Number FY9-4240-003.

To enter Download Mode on the imageRUNNER 2020 / 2016 Series: 1. Hit Additional Functions, 2, 8, and Additional Functions to enter Service Mode. Press the + or - key to scroll through the Service Mode options. Scroll to '#DOWNLOAD'.

Hit the OK key. Iis it necessary to flash the finsher, i mean will it work if didnt flash it. By only downloading: -System (main controller) - Boot (boot program) - PCL (PCL printer kit -J1).

No/ not unless u have an issue with it/ or the firmware is old READ THIS PDF>>important info on Firmware- thnax alot. I have some questions about the following paragraph taken fro the pdf that u gave me.:PROCEDURE: Points to note when upgrading from ver. 10 or earlier to ver. 60 or later: When upgrading from a previous version to v60.02, an “ALL Clear” will need to be performed.